Ham Radio

QRSS

From George Smart's Wiki

Jump to: navigation, search

QRSS is a low power transmission mode used by amateur radio operators in several bands, named after a Morse code signal to slow down. It consists of Morse code sent with very long timings so that the received code is detected by spectrograph instead of by ear. This has the effect of increasing the minimum SNR ratio required. It is possible to receive signals 18000 km away, on just 15mW.


I have also been experimenting with QRSS on 2 metres.


Contents

My Hardware

Testing

My QRSS beacon, based on my Arduino QRSS work, provides an RF output from DDS-60 (Analog Devices AD9851) which then feeds a 1 watt 10 MHz class-C power amplifier. The two combined provide an output power of around 800mW, which is more than suitable for QRSS.


Arduino QRSS Hardware

Secret Nuclear Bunker

For a short while, the beacon is located at the Kelvedon Hatch Secret Nuclear Bunker (GB0SNB). A more permanent station is being worked on by Dave (G7UVW) and me. The QRSS beacon has been enclosed in a weather proof box, and protected form the elements a little. This first image shows the packing to get all the stuff, and a small power supply, inside the weather proof box. I wanted to get the power supply inside to both protect from the rain and to create a little heat inside the box. The Bunker site is remote, and the beacon on the top of a hill, where the temperature is frequently below 0 Celsius - any warmth we could collect is therefore good!


Inside the first attempt


Once it had been thoroughly tested, the lid was tightened down, and I begun to calibrate the temperature. As the inside of The Shack is much warmer than outside, it was necessary to take this thermal difference into account. Something which I initially did wrong and required another trip to the site to put right! You can also see how it's raining quite hard here!


The first attempt


Finally, this last image shows the final resting place for the beacon. It's underneath a porta-cabin (a temporary building structure) which affords some level of shelter from direct rainfall. Then, it is under a plastic water container, which has had the side cut out of it; this reduces the wind chill on the beacon by shielding it from cross winds at the top of the hill. Inside this box, the beacon is wrapped in protective polythene to try and add a little more thermal insulation (this insulation is also part of the issue of why we had to re-calibrate the thermal drift offsets).


It's home at GB0SNB


It's not a pretty sight, but it certainly works well. The antenna is a temporary dipole, made from previously used wire, RF adapters and 10 metres of RG58/U coax back to the beacon - all well taped up! You can just make out the dipole in the image below.


QRSS Dipole


And one more for luck: Dave (G7UVW) with the laptop we used to amend the frequency offsets. Thank god he volunteered as I had left my laptop at work.


Dave (G7UVW) poses

My Signal

As mentioned previously, my 1W PA for 10MHz will put out about 800mW on 30 metres QRSS band. With the Arduino it is possible to create many different kinds of signal. My QRSS signal is three triangles and M1GEO in DFCW Morse code; 5 Hz shift with a 6 second dot length, on approximately 10.140,050 MHz. The image below is a locally captured copy of my transmitted signal. It is repeated continually.


QRSS Signal


Earlier versions used ramps instead of the triangles, which I believed were more easily identifiable; however, due to the use of slant-CW (people encoding Morse code into forward and reverse slashes) it is more useful to use triangles.

Reports

Please send any reports to my email address, using the Contact Me link.

YO7CKQ

15:24, 15/02/2012

I have had a few reports of spots on people's QRSS Grabbers. The first comes care of Sorin (YO7CKQ). He says:

I received today your QRSS beacon on 30 meters band. RIG here: ICOM IC756 PRO III, inverted L antenna,
USB interface and ARGO software. You can see here some print-screen.

I have joined the overlapping printscreens together for a continious image, but the originals are here: A B C D.


Merged report from YO7CKQ


A total distance of 1847 km, from my JO01CN to KN15PA.

PA0TAB

05:20, 15/02/2012

This one I noticed on the PA0TAB QRSS Grabber, found here. It's a little bit weak and with some QSB.


Merged report from PA0TAB


12:30, 17/02/2012

This shows a much stronger reception at the PA0TAB grabber. Note the signal is not in order, but all parts of it fully visible. The triangles break up the Morse code.


Report from PA0TAB


A total distance of 473 km, from my JO01CN to JO33HF.

OZ9QV

09:28, 17/02/2012

This signal, again weak was noticed on OZ9QV Grabber, found here. Again weak with QSB.


Merged report from PA0TAB


A total distance of 912 km, from my JO01CN to JO65CP.

SA2BRJ

09:28, 17/02/2012

This signal was emailed to me by SA2BRJ from his grabber, found here.


Merged report from PA0TAB


A total distance of 1793 km, from my JO01CN to KP03CT.

IZ1KXO

09:10, 19/02/2012

This signal was emailed to me by Paolo, IZ1KXO, from his grabber.


Merged report from IZ1KXO


A total distance of 2006 km, from my JO01CN to JM76.

VE1VDM

20:20, 19/02/2012

This one I noticed on the Big Ears Grabber run by Vernon (VE1VDM), found here. There is a weaker station mixed in with us.


Merged report from VE1VDM


A total distance of 4582 km, from my JO01CN to FN85IJ.

ZL2IK

07:10, 20/02/2012

These spots were emailed to me by Pete, ZL2IK, via the KnightsQRSS mailing list.


Merged report from ZL2IK


A total distance of 18188 km, from my JO01CN to RF74CI. Very pleased!!

W4HBK

09:10, 20/02/2012

These spots were emailed to me by Bill, W4HBK, via the KnightsQRSS mailing list. The first is a short 10 minute spot. The second is a 4-hour long-grab. It shows how strong reception was through out the period (as well as showing drift!).


Merged report from W4HBK


4-hour report from W4HBK


A total distance of 7238 km, from my JO01CN to EM60KJ.

I2PHD

17:13, 22/02/2012

I noticed that I appeared on I2PHD's Argo Homepage in the image showing the application running. I decided to add that to the list, as it was a nice copy.


ARGO Homescreen


A total distance of 963 km from JO01CN to JN45SL.